3.

Cause:                    If garments color and sewing thread does not match with color. It must perform satisfactorily in normal use, meaning that a garment must be abler to withstand normal laundering / dry cleaning / pressing cycle without color loss or shrinkage, seams must not come apart, fabric must not tear and so on.But maintaining an adequate standard of quality also costs effort. The gap between the Cylinder & the Dial should be correctly adjusted as per the knitted loop size. The fabric inspection is done primarily. The quality of a final garment depends on the quality of a fabric when it is received as a roll.

Misalignment of plies: Plies misaligned, resulting in garment parts getting cut with bits missing in some plies at the edge of the spread. You will have the PDF on your device to study offline. Quality assurance and quality control may seem the same thing, but they’re not. The fabric should place in the clean floor. Yarn feeder not properly set. Causes: For the lack of experience or concentration of worker.Remedies: Bottom and top placed correctly and ironing again. Avoid blade deflection 4. Cause:          1.

Stitching fault should be checked   8. This occur due to careless operating by sewing operator Solution: the uneven place seam has to open and again stitch with right measurement. Normally four systems are used for inspection of finished garments.1.

The overhead guide should be directly above cone or the thread package. Here students can get class & chapter wise Class 12 NCERT notes, which is very helpful to understand the subject and its chapter in a good manner. It must ensure that no plies is creased, damage, or have overlapped parts. No more than 4 penalty points can be assigned for any single defect. -When these soft garments are touched then it seems to best touch of garments. In the garment industry quality control is practiced right from the initial stage of sourcing raw materials to the stage of final finished garment. Fabric construction , color fastness, design and the final finished garment. It must be free from defects such as stain, material defects, open seam, loose hanging thread, misaligned buttons and button holes, defective zipper etc.2. The fabric laid on the table and under the glass a light used to checking clearly. Segregate the Spinning & Knitting Machines, with Plastic Curtains or Mosquito Nets, to prevent the fibers flying from the neighboring machines, from getting embedded in the yarn / fabric. Thread trapping at the base of cone Solution: 1. The operator should be skilled for this process because the fabric has to cut by exact marking measurement. Marking process: 2. Reduce Increase thread guides and reduce disc tension. Knitting construction fault:-Loop-Oil stain.-Needle mark.-Sinker mark.-Hole. Keep the record hourly after checking the product. The apparel industry critically depends on the factories, the complex supply chain, and if the best practices are being implemented regarding their quality control systems. -Washing technique create new fashion such as tagging, grinding, destroy, Blasting, whiskering, permanent wrinkle, deep dye, tie dye, p.p spray, hand crapping, p.p spoon zing etc. After reading the chapter, you can refer to our Class 12 NCERT Solutions.

Manufacturing Quality: Manufacturing quality is concerned with the degree to which the garment produced agrees with the sample or specifications. NCERT Solutions for Class 12 Sociology Chapter 3 Social Institutions: Continuity and Change, NCERT Solutions for Class 12 Sociology Chapter 4 The Market as a Social Institution, NCERT Solutions for Class 12 Sociology Chapter 5 Patterns of Social Inequality and Exclusion, NCERT Solutions for Class 12 Sociology Chapter 6 The Challenges of Cultural Diversity, NCERT Solutions for Class 12 Sociology Chapter 2 The Demographic Structure of the Indian Society, NCERT Solutions for Class 12 English – Kaliedoscope, Vistas, Flamingo, NCERT Book Class 12 Home Science Chapter 14 Textile Conservation in Museums. Select chapter you wish to download and its done. 4. Quality control plays a vital role in knit garments production. Solution: 1.

In preproduction quality control, each component of a garment is tested prior to assembling. 3. Washing Section.4.